Oil and Gas

Course catalogue

hits
418
Course code: MUK-147
Course type: E-learning course
Duration: 15 minutes
Language: English
Price: NOK 500,-

Who is this course for?

Personnel who require a basic understanding of the operation of diesel engines and the importance of maintaining good lubrication for their safe operation.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course will provide you with an overview of how diesel engines operate, their components and their use within the industry. It will also outline the importance of maintaining good lubrication for their safe operation.

How will this course benefit my company?

This course will provide personnel with an overview of how diesel engines operate and the importance of maintaining good lubrication for their safe operation.

What standards are referred to in this course?

This course does not refer to specific legislation or standards.

Is there an assessment? 

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: BVS-004
Course type: E-learning course
Duration: 4 hours
Language: English
Price: EUR 380,-

Presentation

This training course provides a general introduction to the corrosion process, the protective coating used to prevent corrosion, the coating process and coating inspection.

Objectives

On completion of the training, students will be able to:

Know the different types of corrosion and their causes.

Understand the corrosion phenomenon and the threat it represents to the structural integrity.

Know the protective coating systems used in shipbuilding.

Be familiar with the constituents, structure and curing prerequisites of the protective coating systems.

Understand the different phases of the coating process and the requirements for successful coating application.

Be familiar with coating inspection procedures and the requirements of the IMO PSPC.

Recognise the different forms of coating failure.

Program

Module 1 - Introduction to Corrosion and Protective Coatings

Corrosion definition

Causes of corrosion

Different forms of corrosion

Corrosion rate

Protective coating systems

Paint coating components

Types of coatings

Technical data sheets

Coating cure

Module 2 - Coating Process and Inspection

Coating process scheme

Surface preparation

Cleaning techniques

Surface preparation

Paint application

Coating durability requirements

Coating inspection

Coating system documentation

Coating inspector qualifications

Inspection procedures and plan

Coating defects

Certificate

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Corrosion and Coating awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Corrosion and Coating, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination.

Course code: MUK-202
Course type: E-learning course
Duration: 30 minutes
Language: English (US)
Price: NOK 500,-

Who is this course for?

Personnel requiring an awareness or understanding of sealed sources of radiation in the US.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to ensure that relevant personnel in the US have a common and consistent understanding of sealed radiation sources.

 

How will this course benefit my company?

By ensuring you have a common and consistent approach to company and industry best practice in relation to US operations involving sealed radiation sources.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MTP-054
Course type: E-learning course
Duration: 60 minutes
Language: English
Price: NOK 1000,-

Who is this course for:
Anyone wanting to take the SRC/VHR-exam.

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
To use VHF you must have a VHF / SRC certificate. With this course you will learn the whole curriculum in a simple and easily understandable way.

How will this course benefit my company?
By ensuring you have the competence to use VHF.

What standards are referred to in this course?
Lovdata - www.lovdata.no
Petroleum Safety Authority - www.psa.no

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: BVS-038
Course type: E-learning course
Duration: 2 hours
Language: English
Price: EUR 200,-

Presentation

 

This training course is about what an effective cyber security risk management should be. Its goal is not to address too many technical questions as the best technical expertise in the world won’t guarantee zero cyber risk. The course aims at providing your Company with a real battle plan: know the assets, know the enemies, organize accordingly and train the effectives. Although this will not be enough to avoid a cyber incident, the severity of the consequences of a cyber incident will depend on the company’s preparedness and ability to manage it.

 

Who the course is for?

 

The course ISM Code and Cyber Risk Management is aimed at anyone interested in understanding how an effective cyber security risk management should be. This may include Top Management of Shipping Companies, Ship Managers, Technical Superintendents, Ship Masters, Officers and Seafarers; Offshore Units Operators and Technical Staff, Shipyards Technical Staff; Surveyors; P&I and/or Insurance Inspectors; etc.

 

Objectives

 

On completion of the training, students will be able to:

Know what cyber security is, the main threats and their consequences.

Understand how to consider the cyber risks in the Safety Management System and how the ISM Code translated into cyber security.

Know the 12 cybersecurity commandments that will help implementing an efficient cyber risk management system.

Course code: MUK-089
Course type: E-learning course
Duration: 3 hours
Language: English
Price: NOK 1500,-

Who is this course for?

Personnel requiring awareness and understanding of Natural Gas & LNG and associated HSE considerations.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to improve your knowledge of Natural Gas Liquid and LNG including transport and HSE considerations.

 

This course contains nine modules:

Module 1: An Overview of Gas Liquids

Module 2: Chemical and Physical Properties of Gas Liquids

Module 3: Liquefied Petroleum Gas

Module 4: Natural Gas Liquids (NGL) Recovery

Module 5: Removal of Natural Gas Impurities

Module 6: Liquefaction of Natural Gas

Module 7: Shore-Based Storage of Gas Liquids

Module 8: Transportation of Liquefied Natural Gas

Module 9: Health, Safety and Environmental (HSE) Issues of Gas Liquids

 

How will this course benefit my company?

To ensure you have an understanding of NLG, LNG, transportation and HSE considerations.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice. 

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: PRO-024
Course type: E-learning course
Duration: 2 hours
Language: English
Price: NOK 2500,-

This course provides an introduction to chemical management, risk assessment of health in relation to work with chemicals. The course is based on the use of ChemiRisk as a tool for risk assessment and CHESS as chemical database. The course consists of three modules (theory, chemical database (CHESS) and using ChemiRisk).

 

Course Content

- Theory

- Substance (CHESS)

- Use of ChemiRisk

 

Course provider: Proactima

Course code: IMIST-002
Course type: E-learning course
Duration: 300 minutes
Language: Brazilian Portuguese
Price: USD 99,-

Who is the course for?

This eLearning course is aimed at individuals who work offshore, in any role, anywhere in the world.

 

Is previous experience required?

The course is designed for existing workers in the oil and gas industry. Completion of this course awards an IMIST certificate valid for four years, after which you will need to sit the course again to refresh your knowledge and earn a new certificate.

 

How will the course benefit me?

The offshore working environment is home to many hazards, which means that it is vital for everyone who goes offshore to have the same baseline level of safety knowledge. This course has been created with OPITO to set a global safety standard by applying a consistent level of safety awareness across nine safety critical areas and is applicable.

The knowledge gained in this course will help you to stay safe in your day-to-day activities offshore. It will also outline some of the systems and procedures in place to manage everyday operations offshore.

 

How will the course benefit my company?

By ensuring that your safety knowledge is at or above the baseline level, your company can rest assured that you are able to work offshore safety and in compliance with regulations and company procedures. Increased safety knowledge helps to prevent incidents and makes your working environment a safer place.

 

What standards are referenced in the course?

This course is written based on the OPITO standard International Minimum Industry Safety Training Standard (IMIST) (5312). As a global standard, the course is not written to meet any specific regional legislation but references industry best practices and standard operating procedures throughout.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 100%. 

The course starts with an optional pre-assessment that checks your existing knowledge of the course topics. The course will restructure so that it only contains the content needed to address the gaps in your knowledge.


Please find pre-course information and learning outcomes here: 

https://mintra.com/implementing-maintaining-opito-standards-policy

Course code: ALT-003
Course type: Classroom course
Duration: 5 days
Language: Norwegian - Exam avail ...
Price: From NOK 16500,-

This course includes all subjects needed to prepare candidates for the rotary drilling well control exam, surface and subsea BOP stack on driller level (Level 3).

A printed course manual and exercise book is provided for all attendees. The IWCF exam is included in the course.

The course has been made on basis of the recommendations for enhancements to well control training, issued by the International Association of Oil & Gas Producers (OGP).

Course Content
- Kick prevention
- Shut in procedures
- Well control methods
- Kill sheet calculations
- Practical simulator training
- Circulation methods
- Practical simulator assessment
- IWCF written exam on the last day (Friday)

Please note! The course is in Norwegian, however you have the option to select the exam language to be English

Course code: MTP-009
Course type: E-learning course
Duration: 2,5 hours
Language: Norwegian
Price: NOK 1200,-

The NORSOK R-003 standard, Safe Use of Lifting Equipment is the industry standard for operating lifting equipment on the Norwegian continental shelf.

The course, “Safe Use of Offshore Cranes”, builds on NORSOK R-003 and is an important means for satisfying governmental regulations for maintaining and verifying competence in the safe use of lifting equipment.

The course focuses ongood work practices, as well as good attitudes and understanding of safety for crane operations, in accordance with the NORSOK R-003 standard.

This course gives an introduction to the new version of R-003 which was launched in 2017.

The course contains references to the 2004 version of R-003, but the course in its entirety will be updated when the new version of R-003 is launched with an updated Appendix B.

 

Course Content:

-Introduction

-Rolls and responsibilities

-Planning and supervising

-Communication

-Supply vessels

-Load bearers

-Chemicals

-Lifting to and from the rig floor

-Using guy wires

-Lifting drilling pipes and casings

-Assembly and disassembly lifts

-Lifting scaffolding material and planks

-Operating blind

-Personnel lifts

Course code: MUK-201
Course type: E-learning course
Duration: 30 minutes
Language: English (US)
Price: NOK 500,-

Who is this course for?

Personnel requiring an awareness or understanding of US fire extinguishers.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to ensure that relevant personnel in the US have a common and consistent understanding of portable fire extinguishers.

 

How will this course benefit my company?

By ensuring you have a common and consistent approach to company and industry best practice in relation to US portable fire extinguishers.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-053
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: NOK 500,-

Who is this course for?

This course is aimed at all personnel involved in operations involving the use of seals, particularly those who are expected to undertake related duties in the workplace.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role.

 

How will this course benefit me?

This course aims to provide an overview of the role and application of seals and gaskets.

 

How will this course benefit my company?

To ensure you have an overview of the role and application of seals and gaskets.

 

What standards are referred to in this course?

The course is made according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-184
Course type: E-learning course
Duration: 150 minutes
Language: English
Price: NOK 1500,-

Who is this course for?
Process Operators and Lab Technicians

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
This course aims to provide an overview of the various types of process chemicals, their use and how they work.

Section 1: Basic Introduction to Chemistry
Section 2: Process Chemicals in the Oil and Gas Industry
Section 3: Identifying the Risks in the Use of Process Chemicals
Section 4: Managing Chemical usage

How will this course benefit my company?
By ensuring you have an overview of the various types of process chemicals, their use and how they work.

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-048
Course type: E-learning course
Duration: 150 minutes
Language: English
Price: NOK 1500,-

Who is this course for?

Personnel who require knowledge or awareness of systems and equipment used for hydrocarbon processing.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to provide personnel with a broad overview of compressors, safety and controls systems, prime movers and ancillary systems.

 

How will this course benefit my company?

By ensuring you have an overview of common hydrocarbon processing systems and equipment and their associated hazards and controls.

 

What standards are referred to in this course?

There are no specific regulations referenced. The course is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: LSI-005
Course type: E-learning course
Duration: 4 hours 30 minutes
Language: English
Price: NOK 1190,-

This course covers the theoretical part of the documented safety training required for slingers and signallers. The course is also suitable as a refresher for crane operators and other personnel who have previously completed training in lifting appliances and lifting gear. The course content deals with selection, control and safe use of the most common lifting gear used in construction, industry, shipping and offshore. Signalling, communication and controlling the load are key topics of the course.

In addition, the course requires that practical training is conducted on applicable work equipment.

 

The course contains 9 modules:

• Lifting equipment, expressions and acronyms

• Slinging, center of gravity, working angles and lifting tables

• Fibre slings

• Lifting gears of chain

• Wire rope slings

• Shackles

• Eye bolts, nuts and lifting lugs

• Signals and signs, and control of load

• Safety regulations for lifting operations

Course code: TES-001
Course type: Classroom course
Duration: 1 day
Language: Norwegian
Price: From NOK 2950,-

The course "Hose assembly – safe appliances" provides a basic introduction to the safe use of hoses and selection of fittings for different applications. Furthermore, the course focuses on the identification of fittings, as well as basic practical training in hose assembly.

After the course, participants will be able to use the hose assembly equipment in a way that maintains a safe and appropriate work process. The course is divided into a theoretical and a practical part and is concluded with a written certification test. The course is conducted according to the standard TR 1803 and Oil and Gas United Kingdom Standard.

Course code: MAE-009
Course type: Classroom course
Duration: 4 days
Language: Norwegian
Price: From NOK 17180,-

This introductory course provides the drilling personnel with basic understanding of well control. Progressing junior staff get a solid background and knowledge of why well control is essential, how well control is maintained, what the indicators are that well control might be lost, and how to regain the control once it has been lost.

Understand the negative consequences associated with loss of well control
Understand the need for detection
Recognize the warning signs of abnormal pressure
Know the actions that should be taken when kick indicators are present
Be familiar with the functions of the bop equipment
Be able to select well control method to regain control
Be able to fill in a IWCF surface and/or subsea kill sheet
Be able to calculate kill mud weight, initial circulation pressure and final circulation pressure
Correctly obtain shut in pressures in the well
Understand the barrier concept
Know the impact pumping cement could have on well control
Obtain sufficient knowledge to pass a written IWCF test with minimum 70% score

Course code: MUK-158
Course type: E-learning course
Duration: 15 minutes
Language: English
Price: NOK 500,-

Who is this course for?

Personnel requiring awareness or understanding of surface preparation methods.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to introduce learners to the requirements for maintaining surface preparation.

 

How will this course benefit my company?

By ensuring you are introduced to the requirements for maintaining surface preparation.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%. 

Course code: ITB-002
Course type: Blended course
Duration: 70 days - 3 years
Language: English
Price: From GBP 460,-

This option is more aimed at delegates with prior knowledge/experience in the workplace assessment, who are looking to consolidate their skills and knowledge to gain a formal certificate.

The e-learning material includes:

How to build a portfolio of evidence that meets the L&D9DI standard 

How to demonstrate knowledge of the above processes and a range of knowledge related to competence assessment in the workplace

What’s included in this course:

• SQA Registration Fee

• Online Induction

• Access to L&D9DI evidence requirements e-modules 

• Full explanation of evidence requirements and access to templates and evidence guides and examples 

• Virtual classroom on request - Introduction to SQA running weekly 

• Comprehensive support from an ITB Assessor to completion

• Assessment and Internal Verification of your submitted evidence

• SQA Certification Successful delegates will receive a certificate from the Scottish Qualifications Authority (SQA)

Virtual webinar sessions running weekly with an ITB Trainer for a Q&A session. Join as many virtual sessions as needed to support to completion of the full SQA qualification. 

Those who assess in the workplace using direct and indirect methods of assessment using examples: observation, questioning, work product, professional discussions, simulations, written evidence such as witness statements and candidate statements and RPL.

 

Assessment Requirements

Delegates will be required to submit a portfolio of evidence covering all of the Performance and Knowledge Criteria for the L&D9DI Unit. They must submit, as a minimum, assessment-related documentation that provides evidence for the elements listed below, for two candidates, covering two assessments per candidate: 

• Preparing to assess 

• Planning assessments 

• Assessing candidate’s performance and knowledge 

• Confirming progression and achievement

Delegates must use a range of assessment methods, including observation, questioning and work product. 

 

Delegates will also need to be observed carrying out part of the assessment process by an ITB (or NVQ-level) assessor and participate, with other assessors in their workplace, in standardisation practice.

Course code: MUK-169
Course type: E-learning course
Duration: 120 minutes
Language: English
Price: NOK 1500,-

Who is this course for?

All personnel who are involved in offshore drilling.


Is previous experience required?

No previous experience is required to complete this course. 


How will this course benefit me?

This course aims to provide an overview of well control and the systems used in the process and is based upon the International Well Control Forum (IWCF) Level 1 Syllabus.


How will this course benefit my company?

This course will benefit companies by ensuring personnel have an understanding of well control and the relevant systems.


What standards are referred to in this course?

No standards or regulations are referenced in this course.


Is there an assessment?

Yes

Hits per page
| 1 ... 13 ... |