Course catalogue

Who is this course for?

Personnel who require an awareness and understanding of various water injection methods.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide all relevant personnel with the knowledge required to understand water injection. 

This course contains nine modules:

Module 1: Introduction to Water Injection

Module 2: Reservoirs and Rock Properties

Module 3: Waterflooding

Module 4: Injection Water Impurities

Module 5: Water Treatment

Module 6: Water Injection Systems

Module 7: Water Quality Monitoring

Module 8: Well Design and Construction

Module 9: Operation of the Water Injection System

How will this course benefit my company?

To ensure you have the knowledge required to understand water injection.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

All relevant personnel.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role.

How will this course benefit me?

You will be introduced to the purpose of separation.

This course contains ten modules:

Module 1: The Purpose of Separation

Module 2: Reservoir Fluids

Module 3: The Principles of Separation

Module 4: Separator Types

Module 5: Separator Construction

Module 6: Multi-stage Separation

Module 7: Separator Control

Module 8: Separator Operation

Module 9: Problems Associated with Separators

Module 10: New Separation Technology

How will this course benefit my company?

Ensure you are introduced to separation.

What standards are referred to in this course?

The course is made according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Hensikten med opplæringen er å gi blivende riggere en god praktisk grunnopplæring i sikker bruk av riggerutstyr. Opplæringen skal gi elevene god innsikt i prinsippene for riggutstyrets konstruksjon, virkemåte, bruk og vedlikehold, slik at uhell og ulykker i forbindelse med riggoperasjoner unngås. Riggoperasjon: Bruk og sammenstilling av transportabelt løfteutstyr og/ eller manuelle/ kraftdrevne vinsjer, taljer etc. som benyttes ved horisontal og/ eller vertikal forflytning av last. Opplæringen dekker den nødvendige teoretiske og praktiske opplæringen som er nødvendig for å kunne gjennomføre selvstendige riggoperasjoner. Opplæringen avsluttes med en praktisk prøve.

Modul O-2.2: Fallsikring - Søylesvingkran / enkel traverskran - Taljer / vinsjer. (16 timer opplæring).

Modul O-3.2: Rigging (32 timer opplæring) Beviset kan utstyres med opplæringsbedriftens/virksomhetens logo.

This course is only available in Norwegian.

Who is this course for?

Personnel who require an awareness and understanding of methods of oil and gas recovery.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide learners with an introduction to oil and gas recovery methods

How will this course benefit my company?

By ensuring you are introduced to the various ways oil and gas are recovered from the well.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Induction course in HSE is designed so that participants will have the first necessary expertise to ensure safety challenges in their daily work. This occurs in part through increased awareness of what is valuable and should be prioritized. The course also draws attention to the main framework governing the HSE The course is designed in order to create interest and motivation to work with HSE in the workplace.

Course contents

The course is divided into three topics:

-Care! - To take care of each other

-Terms and conditions - Laws, regulations and rules

-The challenging life - how to work without going wrong

Participants will

-Be motivated to work with safety in the workplace.

-Understand the relationship between a good safety work and preventing loss of important values such as life, health and nature in balance.

-Get an introduction to the main control elements of the HSE 

-Get advice on how they can work safely under time pressure and stress situations

Course provider: Proactima

Who is this course for?

Personnel requiring knowledge or awareness of hot work hazards and controls in the US.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide learners with an awareness of US best practice in relation to hot work.

How will this course benefit my company?

By ensuring you are aware of US best practice in relation to hot work.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Process and Production personnel

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?

By ensuring you have an overview of industry best practice associated with gas treatment

This course contains seven modules:

Module 1: Introduction to Gas Treatment

Module 2: Problems Associated with Water in Gas Streams

Module 3: Liquid Desiccant Dehydration

Module 4: Solid Desiccant Dehydration

Module 5: Alternative Gas Dehydration Processes

Module 6: Acid Gas Removal Unit

Module 7: Removal of Other Impurities in Raw Gas Streams

How will this course benefit my company?

By ensuring you have an overview of industry best practice associated with gas treatment

What standards are referred to in this course?

This course does not refer to specific legislation or standards.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

All personnel involved in warehouse safety operations in the workplace.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to identify the hazards specific to warehousing and provide advice on how to avoid these hazards.

How will this course benefit my company?

By ensuring you are able to identify the hazards specific to warehousing and provide advice on how to avoid these hazards.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Personnel requiring an awareness and understanding of power generation systems and their associated risks.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to proivde learners with an overview of power generation systems used offshore.

How will this course benefit my company?

To ensure you have an overview of the power generation systems used offshore including hazards and their associated controls.

What standards are referred to in this course?

The course is made according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Section 7 of the “Safety Regulations for Work and Operation of Electrical Equipment and Installations” (FSE) sets requirements for yearly FSE training for relevant personnel. This e-learning course takes you through the requirements of the regulations and gives you training and instruction in FSE. The course focuses on safety for work on low voltage installations offshore.

The course also provides first-aid instruction and training. CPR training must be completed separately.

In accordance with section 7 of FSE, FSE and and first-aid training must be completed at least once a year. In order to meet the requirement for being able to provide first aid in the event of electrical accidents, you also need to complete yearly practical training in CPR (mouth-to-mouth and heart compressions).

This course addresses a variety of issues and covers how to prevent electrical accidents, routines in the event of accidents, and theoretical first aid, and aims to help prevent harm to people, equipment, and installations.

The course covers the following topics:

- Act and Regulations
- Purpose
- Responsibility
- Participants and roles
- Internal control regulations

At the beginning of the course you can take a pre-test, where you get the opportunity to show your skills. If you pass the pre-test, you do not have to go through the entire course.

The course provides employees who are responsible for drinking water offshore, or tasks associated with this, increased knowledge and understanding to provide good, sufficient and safe drinking water to the staff on board.

Satisfy the requirements for competence in relation to the Norwegian Public Health Institute’s guidelines: “Nok, godt og sikkert drikkevann offshore.”

After the course you should:
- Know about and be able to orient yourself in the relevant regulations with emphasis on the public health department's supervisor “Nok, godt og sikkert drikkevann offshore"
- Understand the distinction between drinking water affect the installation's water system, and people's health
- Understand the purpose of the various laboratory analyzes used to monitor the quality of water
- Know which analyzes offshore employees are responsible for themselves, and what responsibilities they have in connection with the analyzes that must be sent to an accredited laboratory
- Be able to interpret results from laboratory analyzes and know what action offshore staff must implement when results are abnormal and/or critical
- Understand the structure of a drinking water system offshore, and where in the system offshore personnel has responsibility for operation and maintenance

Please note: this course is also available in an Norwegian-language version.

The course is delivered by the accredited laboratory SINTEF NORLAB AS. 

Who is this course for?
Trainee Oil and Gas Operations Technicians / Deck Crew

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
This course aims to provide an introduction to the use of storage tanks

How will this course benefit my company?
By ensuring you are introducted to the use of storage tanks

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Personnel requiring awareness or understanding of typical chemicals in use for well operations.

Is previous experience required?

You do not need prior knowledge or experience to complete this course

How will this course benefit me?

This course aims to provide learners with an awareness of industry best practice for working with chemicals in offshore drilling and well operations

How will this course benefit my company?

By ensuring you are aware of industry best practice for working with chemicals in offshore drilling and well operations

What standards are referred to in this course?

Offshore Chemicals Regulations (OCR) 2002

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Everyone working on high voltage installations.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?

The course meets the requirements set in § 7 of the ""Safety Regulations for Work and Operation of Electrical Equipment and Installations- FSE"", that relevant personnel shall be given annual training and instruction in FSE. The course also provides the necessary training and instruction in first aid, focusing on electrical injuries, with the exception of the mandatory practical training in cardio-pulmonary resuscitation (CPR).

The regulations of various authorities make FSE applicable to all those working with electricity, whether on board ship, on platforms or on land. This course is suitable for all, regardless of which industry you work in. 

The authorities require that training in FSE and first aid in the event of electrical accidents is undertaken at least once a year. No more than 12 months shall elapse between training courses.

How will this course benefit my company?

By ensuring you have the knowledge and competence to be working on high voltage installations.

What standards are referred to in this course?

 § 7 of the ""Safety Regulations for Work and Operation of Electrical Equipment and Installations- FSE""

Is there an assessment?

The fast track version of the FSE course starts with a pre-test which checks the participant's knowledge of FSE. Depending on the answers given, the participant will get a course that is tailored to the level of knowledge revealed in the pre-test. The fast track version of the course is suitable for all but is particularly practical for those undertaking refresher training in FSE. 

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course provides an introduction to chemical management, risk assessment of health in relation to work with chemicals. The course is based on the use of ChemiRisk as a tool for risk assessment and CHESS as chemical database. The course consists of three modules (theory, chemical database (CHESS) and using ChemiRisk).

Course Content

- Theory

- Substance (CHESS)

- Use of ChemiRisk

Course provider: Proactima

For English version of this course, please enrol to "OG1 Basic emergency management, English (e-learning)" Course.

Proactive emergency response management involves identifying measures that can control the development in the desired direction and take action before circumstances force one to do it.
This course is the first step of the way to handle such situations and thus participate in 2nd or 3rd line emergency response organization onshore.

Course content:
• Introduction
• Defined hazard and accident situations
• External resourses
• The structure and use of emergency plan
• Training and exercises
• Evaluation and improvement
• Stress reaction in an emergency organisation
 

Target group:
Target group is all personnel who will participate in 2nd and 3rd line emergency response work in the company.

Learning methods:
E-learning. It is recommended that e-learning course is followed up with collection, training and exercises. Please contact course provider Proactima for a customized business services.

The course gives you a basic understanding of the principles of intrinsically safe loops (IS) in potentially explosive areas.

After completing the course, the candidate will have acquired the necessary knowledge about the design of intrinsically safe (IS), choice of equipment, inspection and maintenance in potentially explosive areas.

Our aim is to ensure that the employees are motivated to work safely and securely.

The course lasts 5 hours and the course certificate is valid for 5 years

The e-learning course can also be used as a refresher after 5 years

Themes:

• Understand the general principles for the type of specific protection and correct marking of components approved in intrinsically safe systems (IS)

• Current standard for Exi

• Construction and assessment of intrinsically safe equipment

• Assessment and concrete use of “simple apparatus app”

• Be able to choose and install the correct Exi equipment in hazardous areas according to the standards IEC 60079-14 and 60079-25

• How to work safely with IS

• Competence requirements for performing work on Exi installations

• How to verify and calculate an Exi circuit

• Know where to find and how to read relevant standards, data sheets, product sheets and other relevant literature

Who is the course for?

All personnel, especially those who require an overview of produced water systems.

Is previous experience required?

No previous experience is required to complete this course.

How will the course benefit me?

This course is designed to provide you with a basic knowledge of how water is removed from oil and gas reservoirs and how it is treated prior to reuse or disposal.

How will the course benefit my company?

This course helps to ensure that all personnel apply a common approach to both company and industry best practice in relation to managing produced water.

What standards are referenced in the course?

• The Offshore Petroleum Activities (Oil Pollution Prevention and Control) Regulations 

• The Registration, Evaluation, Authorisation and Restriction of Chemicals Regulation (REACH)

• OSPAR Harmonised Mandatory Control Scheme (OSPAR HMCS)

• US Environmental Protection Agency Federal Insecticide, Fungicide and Rodenticide Act (FIFRA)

• Methodology for the Sampling and Analysis of Produced Water

• Environmental Protection Agency's Method 1664

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course covers the theoretical part of the documented safety training required for slingers and signallers. The course is also suitable as a refresher for crane operators and other personnel who have previously completed training in lifting appliances and lifting gear. The course content deals with selection, control and safe use of the most common lifting gear used in construction, industry, shipping and offshore. Signalling, communication and controlling the load are key topics of the course.

In addition, the course requires that practical training is conducted on applicable work equipment.

The course contains 9 modules:

• Lifting equipment, expressions and acronyms
• Slinging, center of gravity, working angles and lifting tables
• Fibre slings
• Lifting gears of chain
• Wire rope slings
• Shackles
• Eye bolts, nuts and lifting lugs
• Signals and signs, and control of load
• Safety regulations for lifting operations