Course catalogue

Presentation 

This training course provides general information about welding of aluminium structures. It contains an introduction to aluminium properties and describe the main issues regarding weldability of aluminium and its alloys. 

Objectives 

On completion of the training, students will be able to: 

Know the properties of aluminium and its alloys comparing to steel 

Understand the issues regarding weldability of aluminium alloys 

Recognize the main problems that can arise during design and production of aluminium ship’s structures 

Know the suitable welding processes for joining of aluminium ship hull 

Understand the application of bimetallic joints. 

Program 

Properties of aluminium alloys 

o Specific properties 

o Heat treatable and non-heat treatable aluminium alloys 

o Marine aluminium alloys 

o Designation of aluminium alloys 

Weldability of aluminium 

o Characteristics of aluminium referring to welding 

o Main issues: gas porosity, oxide inclusions and lack of fusion, hot cracking, reduced 

strength in the weld and heat affected zone, distortion 

o Choice of filler material 

Welding processes for aluminium 

o MIG aluminium welding 

o TIG aluminium welding 

o Typical defects in aluminium welding 

Joining of steel and aluminium in shipbuilding 

o Bimetallic strip for transition joints 

Preparation and design of welds 

o Guidelines for aluminium joint design 

o Examples of joints 

o Application of backing 

o Defects caused by poor preparation 

o Recommendations for aluminium welding

Certificate 

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Aluminium Welding awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Aluminium Welding, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination. 

Deltakerne vil få en god og sikker innføring i høytrykkstestingsutstyr, teori og praksis. Etter endt kurs skal deltakerne kunne bruke trykkstestingsutstyr på en sikker måte, slik at ulykker og skader unngås.

Hensikt:

Hensikt: Hensikten med innføringskurs i trykktesting er å gi den enkelte kursdeltager de grunnleggende kunnskaper om forberedelser, planlegging, utførelse og dokumentering av trykktesting som disiplin.

Innhold:

Svakheter i sammenføyninger og materialer

Omregningstabeller PSI - BAR

Hydrostatisk og Pneumatisk trykktesting

Sikkerhet ved trykktesting og fysiske barierer

HMS - Bruk av personlig verneutstyr

Generelle prosedyrer ved trykktesting / Eksempel

Fittings og høytrykkslanger - Trykklasser

Gjengetyper, flenser, ventiler, pakninger og bolter

Ulike metoder for trykktesting

Trykktestingsutstyr

Bruk av trykktestingsutstyr i praksis. Trykktesting

This course is only available in Norwegian.

Presentation 

This training course provides a general introduction to dynamic positioning systems, which are computer-controlled systems that automatically maintain the vessel's position and heading by using their propellers and thrusters. 

Objectives 

On completion of the training, students will be able to: 

Get familiar with dynamic positioning systems. 

Know the main components of dynamic positioning systems, equipment used and installation. 

Know the Class requirements in terms of surveys and tests of dynamic positioning systems 

Program 

History 

Characteristics and scope of DP systems 

Applications 

Equipment class 

Classification notations 

System configuration: power system, thruster system, control system, position reference systems, computer system, display system 

Redundancy 

o Redundant systems 

o System failures 

o Redundancy concept 

o Terms 

o Single fault tolerance 

o FMEA 

Design environment 

Essential non-DP systems 

Performance analysis 

Operational requirements 

System components 

o Power system 

o Thruster system 

o DP control system 

o Position reference system: acoustical, taut-wire and other reference systems 

Scope of DP surveys 

o Inspections at works 

o Surveys during construction, tests and trials 

o Surveys during operation: Annual and Renewal surveys, operational test, Occasional surveys

Certificate 

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Introduction to DP System awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Introduction to DP System, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination.

Hensikten med opplæringen er å gi truckførere allsidig praktisk opplæring og øvelse i sikker bruk av truck, slik at ulykker i forbindelse med bruken unngås. Opplæringen skal gi fører så gode kjøreferdigheter at vedkommende selvstendig på en sikker måte skal kunne gjennomføre oppdrag med truck.

Truckfører må imidlertid gjennomføre typeopplæring på den trucken som til enhver tid benyttes i tillegg til sertifisert sikkerhetsopplæring. Opplæringen avsluttes med en praktisk prøve som innbefatter kontroll og bruk av aktuelle trucker.

Bestått praktisk prøve på aktuelle trucker vil være grunnlag for utstedelse av kompetansebevis for fører av truck

Modul 1.1 (8 timer) Arbeidsmiljø, ansvar og konsekvenser

Modul 2.2 (14 timer) Truck 

Modul 3.2 (6 timer) Praktisk bruk

Modul 4.2 Bedriftsoppl. - 20 timer Oppl.virksomhet-14 timer

The course is only available in Norwegian.

Hensikten med kurset er å gi blivende riggere en god teoretisk grunnopplæring i sikker bruk av: Fallsikringsutstyr og enkle løfteinnretninger (enkle travers- og søylesvingkraner, håndtaljer, luft- og eltaljer og transportable vinsjer.Opplæringen gir kandidaten god innsikt i prinsippene for fallsikringsutstyrs, enkle løfteinnretningers og transportable vinsjers konstruksjon, virkemåte, bruk og vedlikehold, slik at uhell og ulykker i forbindelse med riggeoperasjoner unngås.

Deltakeren må ha fullført G11 stroppekurs før kursstart.

Opplæringen dekker den nødvendige teoretiske som er nødvendig for å kunne gjennomføre det praktiske riggekurset, Modul O 3.2.

Kurset avsluttes med en teoretisk prøve. 

Kursinnhold
- Fallsikringsutstyr
- Travers- og søyle- svingkraner
- Håndtaljer, luft- og el-taljer
- Transportable vinsjer
- Avsluttende teoretisk prøve

This course is only available in Norwegian.

This course combines self-study by e-learning and classroom training with demonstrations and examples which is useful when working in explosive atmospheres.

The concept intrinsic safety is unlike the other Ex protection concepts as it is a system concept. Therefore, it is necessary to understand the system as a whole, how the environment and individual components affect the system to maintain the integrity of the intrinsically safe system.

Provided in association with Astutis, NEBOSH Learning Partner 807.

The NEBOSH International Diploma in Occupational Health and Safety is an advanced health and safety qualification. Equivalent to an undergraduate degree in OHS. The NEBOSH Diploma is NEBOSH's flagship qualification. It is recognised by employers and professional bodies in over 180 countries around the world!

The qualification will develop competence in all areas of health and safety so you can reduce risk in dangerous environments and keep people safe. It is the ideal course if you want a successful, long-term career in health and safety.

Unit A: Managing Health and Safety

This unit provides an in-depth understanding of the key areas for managing health and safety, covering moral, economic and societal drivers, health & safety law and health & safety management systems. 

A1 - Principles of health & safety management

A2 - Principles of health & safety law

A3 - Criminal Law

A4 - Civil Law

A5 - Loss causation and incident investigation

A6 - Measuring and reviewing health and safety           

A7 - Identifying hazards, assessing and evaluating risk

A8 - Risk control

A9 - Organisational factors

A10 - Human factors

A11 - The role of health & safety practitioner

Unit B: Hazardous Agents in the Workplace

Unit B details all major aspects of managing chemical, biological, physical and physiological hazards in the workplace.

B1 - Managing Occupational Health

B2 - Identification, assessment & evaluation of hazardous substances

B3 - Control of hazardous substances

B4 - Monitoring and measuring

B5 - Biological agents

B6 - Physical agents - noise and vibration

B7 - Physical agents - radiation

B8 - Mental ill-health & dealing with violence & aggression at work

B9 - Musculoskeletal risks and controls

B10 - Work environment risks and controls

Unit C: Workplace and Work Equipment Safety

Unit C provides a thorough understanding of how to create and manage safe working environments, covering welfare, fire, dangerous substances, work equipment, electricity, construction and transport. 

C1 - Workplace welfare requirements and specific workplace issues

C2 - Fire and explosion

C3 - Workplace fire risk assessment

C4 - Storage, handling and processing of dangerous substances

C5 - Work equipment (general)

C6 - Work equipment (workplace machinery)

C7 - Mobile, lifting, access and work at height equipment

C8 - Electrical safety 

C9 - Construction & works of a temporary nature - hazards and controls

C10 - Workplace transport and driving for work

Who is the course for?

This course is for those involved in performing process isolations, such as plant managers, operations staff, HSE managers and maintenance personnel.

Is previous experience required?

No previous experience is required to complete this course.

How will the course benefit me?

This course will provide learners with safety information for working with process isolations.

How will the course benefit my company?

This course will provide learners with an understanding of the hazards involved in process isolations and ways to mitigate the likelihood of accidents occurring during process isolation operations.

What standards are referenced in the course?

There are no standards or legislation referenced in this course.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Provided in association with Astutis, NEBOSH Learning Partner 807.

The NEBOSH International General Certificate in Occupational Health and Safety (IG) is one of the leading health and safety qualifications recognized globally.  It helps develop your understanding of general workplace issues and how they can be applied in different sectors around the world.

The new NEBOSH International Certificate focuses on the role of a real-life health and safety professional. It looks at the real, everyday risks that people encounter and how to manage them to help protect people and profits. 

You'll develop the essential risk management skills to create a safe and healthy workplace. And, you’ll have the foundation knowledge to make recommendations to your employer to help them improve health and safety management.

Upon completion of this course, learners will be able to:

• Justify health and safety improvements using moral, financial and legal arguments

• Advise on the main duties for health and safety in the workplace and help their organisation manage contractors

• Work within a health and safety management system, recognising what effective policy, organisational responsibilities and arrangements should look like

• Positively influence health and safety culture and behaviour to improve performance in their organisation

• Do a general risk assessment in their own workplace – profiling and prioritising risks, inspecting the workplace, recognising a range of common hazards, evaluating risks (taking account of current controls), recommending further control measures, planning actions

• Recognise workplace changes that have significant health and safety impacts and effective ways to minimise those impacts

• Develop basic safe systems of work (including taking account of typical emergencies) and knowing when to use permit-to-work systems for special risks

• Take part in incident investigations

• Help their employer to check their management system effectiveness – through monitoring, audits and reviews

Objective: The aim of the training is that those who are given training receive a repetition of acquired competence in theoretical and practical understanding of safe work operations / emergency operations with offshore cranes so that accidents and incidents can be avoided.

The aim of the training is that those who are given training receive a repetition of acquired competence in theoretical and practical understanding of safe work operations / emergency operations with offshore cranes so that accidents and incidents can be avoided.

The training is according to training plan module P-4.1.1 covers repetition requirements in NORSOK R-003.

Validity:

3 years according to NORSOK
2 years according to OPITO

Holders of a G5 certificate must meet the requirements for updating through module P-4.1.1 "Offshore crane simulator" within three years, and then update this every three years. If this update is not carried out the certificate is still valid, but the G5 certificate holder cannot operate a crane until the requirements for the simulator training have been completed.

Content:

- Introduction
- Accidents and accidents with offshore cranes
- Laws, regulations, standards, regarding offshore cranes
- Operational limitations of crane operations
- Planning of lifting operations (TBT, SJA, Work permits)
- Internal lifting, loading and lifting from / to supply boats, critical lifts, transport of personnel
- Emergency operations
- Communication
- Practical operations use of simulator
- Theoretical and practical exam

Course goal: This course aims to provide all relevant personnel with an overview of best practices in Mechanical Isolations

Course Sections:

1. Introduction to Mechanical Isolations

2. Roles and Responsibilities

3. Safety Critical Manual Valves (SCMVs)

4. Planning Isolations

5. Performing Isolations

6. Isolation Security

7. HP/LP Systems

8. Reinstatement of Plant

Doel van de cursus: Deze cursus is erop gericht al het relevante personeel een overzicht te geven van de beste praktijken inzake mechanische isolaties

Cursusdelen:

1. Introductie tot mechanische isolaties

2. Functies en verantwoordelijkheden

3. Handbediende veiligheidskritische kleppen (HVKK's)

4. Isolaties plannen 

5. Isolaties uitvoeren

6. Isolatiebeveiliging

7. HD/LD-systemen

8. Herplaatsing van installatie

Hovedmålet med kurset er at den som gis opplæring tilegner seg tilstrekkelige kunnskaper om sikker bruk av løfteredskap slik at ulykker ved bruk unngås.

Regelverksreferanse:

Modul 1 - 2.3

Upon completion of the Global Wind Organization (GWO) Basic Safety Training (BST), delegates will have awareness of the dangers that arise when working in the wind industry and how to control and reduce these dangers.

The course participants will gain the knowledge and skills to handle manual lifting properly and ensure their own safety with proper lifting in accordance with ergonomics.

The aim of this module is to encourage positive manual handling behavior and train delegates ability to perform manual handling tasks in a safe manner in the wind turbine industry / environment.

The course covers the requirements for training of personnel and refresher courses both onshore and offshore wind in accordance with:

- Global Wind Organization (GWO)

- Labor Inspection (Regulations)

Competence for "Manual handling" must be maintained in accordance with guideline in the GWO standard. It shall be conducted refresher training every 2 years.

Presentation 

This training course provides a general overview of the requirements of the AFS Convention and the anti-fouling systems used for new constructions and during ships operational life.

Objectives

On completion of the training, students will be able to: 

Understand the aim of the anti-fouling systems and their impact on the environment. 

Know the requirements of the AFS Convention. 

Be familiar with the applicable documentation and related certificates. 

Program 

What is fouling and how do anti-fouling systems work 

Influence on the environment 

Composition of anti-fouling systems 

The AFS Convention and regulations 

Applicability of AFS Convention for new and existing ships 

Regulation (EC) No. 782/2003 

Survey and certification 

o Types of surveys 

o Scope of Initial surveys for new and existing ships 

o Other surveys 

o Certificate issuance 

o The validity of the IAFS Certificate 

o Type approval certificates

Certificate 

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Anti-Fouling Systems awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Anti-Fouling Systems, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination.

Presentation

This training course aims at providing an overview of the Port State Control background, organisation and procedures. It includes a description of the Port State Control inspection process, the criteria for selection of ships for inspection and the most common detainable deficiencies.

Objectives

On completion of the training, students will be able to:

Know the background and organisation of the various Port State Control regimes around the world

Understand the Port State Control procedures, the criteria for selection of ships for inspection and the inspection process

Know the various publications issued regularly by the different Port State Control regimes 

Get familiar with the most common deficiencies which may lead to ship’s detention

Program

PSC background and organisation

Purpose

Regulations

Regional Port State Control organisations

PSC procedures

Relevant instruments

Selection of ships for inspection

Inspection and selection scheme – Scope, priority and frequency of inspection

Paris MOU – New Inspection Regime (NIR) factors

PSC inspection process

Initial inspection

Clear grounds for more detailed inspection

More detailed inspection

Ship detention

Banning of ships

Publication of information

Detainable deficiencies

Examples of detainable deficiencies

Under SOLAS Convention

Under Load Lines Convention

Under MARPOL Convention

Under Chemical and Gas Codes

Under STCW Convention

Under ILO Conventions

Statistics from various PSCs

Certificate

On completion of the training program, the student will be awarded: 

A Certificate of Port State Control, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Port State Control is obtained after completion of the course and passing the online test.

Hovedmålet med opplæringen er å gi en innføring i Norsok standard R-003 og R-005 slik at kursdeltakerne blir familisert med - og kan bruke Norsok standard som oppslag i sitt daglige arbeid.

Regelverksreferanse:

Modul O-1.2

Ce cours est conçu pour :

• Présenter les grandes lignes du processus d'Évaluation de l'impact environnemental (EIA)

• Décrire les contrôles législatifs en vigueur concernant l'EIA 

• Identifier les projets pour lesquels une Déclaration environnementale (ES) est obligatoire, et quand une révision d'une ES existante peut être nécessaire

• Identifier les activités pour lesquelles une Orientation de l'EIA peut être requise, plutôt qu'une ES

• Identifier les activités qui sont « exclues » et qui n'exigent ni ES ni Orientation de l'EIA

• Décrire les différentes étapes du processus d'EIA et identifier les types de consultations qui doivent être effectuées

• Identifier les zones qui doivent être soigneusement étudiées afin de déterminer l'impact potentiel sur leur environnement, et

• Connaître les délais pour mener une ES ou une Orientation de l'EIA

Presentation

This training course provides a general introduction to the most important maritime regulatory bodies: the International Maritime Organisation (IMO), the International Association of Classification Societies (IACS) and the European Maritime Safety Agency (EMSA).

Objectives

On completion of the training, students will be able to:

Understand the mission and structure of IMO, know the IMO requirements and the main International Conventions, and understand the process of acceptance, adoption and implementation of International Conventions.

Know the history of IACS and its mission, understand the IACS organization and the role of each entity, and know the main types of documents issued by IACS and how they are implemented.

Understand the European context, the role of the European Maritime Safety Agency (EMSA), and know the key points of the EU Regulation on common standards for ship inspection and survey organisations.

Program

Module 1 – IMO

IMO Mission

IMO History

IMO Organisation

IMO Regulations

Implementation of IMO Regulations

IMO Technical Assistance

Module 2 – IACS

IACS History

IACS membership evolution and current members

Membership criteria

The mission of Classification Societies and what Classification Societies do not do

IACS aims

IACS values – Leadership, technical knowledge, quality performance, transparency

IACS Organisation

Work programme and work process

IACS Panels

IACS main documents

Module 3 – EMSA

The European context

EMSA purpose and mission

EMSA structure

Regulation (EC) No 391/2009 

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Maritime Regulatory Bodies, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Maritime Regulatory Bodies is obtained after completing the course and passing the online test.

Presentation

This training course provides an overview of the general hazards existing on board ships, the appropriate protective equipment to be worn, the precautions to be taken before entering a confined space and other dangerous situations.

Objectives

On completion of the training, students will be able to:

Know the general principles and the hazards existing on board ships

Get familiar with the different personal protective equipment and their applications 

Understand the hazards related to confined space entries, and the precautions to be taken

Know the precautions to be taken about the various dangerous situations likely to be found on board ships.

Program

General principles

Risk control structure

Personal Protective Equipment (PPE)

o Protection of the head

o Protection of eyes and face

o Respiratory protection

o Protection of the feet

o Hearing protection

o Protection of the body

o Protection against fall from height

o Protection of the hands

o Other safety equipment

Safe boarding of ships and offshore units

General precautions while working on board

o Slips, trips and falls

o Internal inspections

o Engulfment

o Fire & explosion

o Hazardous materials

o Air quality & Oxygen rate

o Main points of attention

Confined spaces

o General precautions

o Entry permit

o Rescue attempts

o Particularly dangerous spaces

Other dangerous situations

o Use of rafts or boats for inspections

o Working at height

o Pressure tests

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Personal Safety on Board Ships, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Personal Safety on Board Ships is obtained after completion of the course and passing the online test.