Oil and Gas

Course catalogue

hits
656
Course code: MUK-156
Course type: E-learning course
Duration: 1 hour
Language: English
Price: NOK 1000,-

Who is the course for?

Personnel requiring an awareness or understanding of typical flanges and gaskets and their functions.

 

Is previous experience required?

It is recommended you have operational experience prior to undertaking this course.

 

How will the course benefit me?

This course aims to provide learners with an overview of typical flanges and gaskets found in the Oil and Gas Industry.

 

How will the course benefit my company?

By ensuring you are introduced to the role of of typical flanges and gaskets in operations.

 

What standards are referenced in the course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: IKM-005
Course type: Classroom course
Duration: 3-4 days (see speci ...
Language: Norwegian
Price: From NOK 12000,-

Kurset er basert på 4 dager og består av klasseromsundervisning og praktiske oppgaver der hydrauliske vri og strekkverktøy samt momentnøkkel blir gjennomgått.

 

Kurset avsluttes med en teoretisk og praktisk eksamen med sensor. 

Kursinnhold:
Kurset tar for seg følgende tabeller i EN1591-4:2013:
1, 2, 3, 6, 7, 8, 9 og 10.

Hovedoppgavene under opplæringen vil være:
- Hva skjer når du tiltrekker bolter og muttere
- Pakninger / tetningsringer – Typer og applikasjoner og installasjon
- Flenstetningspor / overflateruhet
- Rett montering av flensforbindelser
- Smøremiddel på bolter og mutter
- Sikker bolt last verdi for bolten
- Viktigheten av den gjenværende bolt lasten
- Metoder for bolt opptrekking
- Manuelt vri verktøy
- Hydrauliske muttertrekkere
- Hydraulisk strekkverktøy
- Typer flenser
- Rør detaljer
- Prosedyrer og rapportering
- Skjeve forbindelser (ikke parallelle flenser)

Praktiske opplysninger:

Oppmøte adresse kurs; IKM Kurs og kompetansesenter,

Ljosheimvegen 16, N-4051 Sola

Avbestilling
Ved avbestilling senere en syv dager før kursstart, belastes Kunden med full pris. En kunde kan endre på hvem som deltar på kurset til en dag før kursstart uten at kursavgiften økes.
Ved sykdomsfrafall må gyldig legeerklæring fremvises for at kursavgiften skal bortfalle.Vi tar forbehold om avlysning av kurs ved sykdom, for få påmeldte eller force majeure.

Tidspunkt
Første kurs dag kl. 09:00, til ca. kl. 15.30. 
påfølgende dager 08:30 til ca. 15:30

Tekniske forespørsler angående kurssenteret

Har du behov for å få svar på tekniske spørsmål rundt våres kurssenter eller kurs tilbud utover det som ligger tilgjengelig på  http://www.trainingportal.no  så vennligst ta kontakt på mail: kurs.ikmtesting@IKM.no eller ring 48 89 45 52 Tor Arne Johannesen

-------------------------------------------------------

 

Course code: IN-08
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: GBP 40,-

Who is the course for?

This course is for any person who interacts with, or is responsible for, the specification, design, operation and maintenance of assets that employ safety instrumented systems.

Is previous experience required?

No previous experience is required to complete this course.

How will the course benefit me?

This course will provide you with an awareness of the purpose and nature of safety systems deployed to protect people, the environment and plant in the areas that you work.

How will the course benefit my company?

By ensuring personnel have an understanding of safety instrumented systems.

What standards are referenced in the course?

IEC 61508

IEC 61511

IEC 62061

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-007N
Course type: E-learning course
Duration: 45 minutes
Language: Norwegian
Price: NOK 500,-

Course Goal: To increase learners’ awareness of the risks of hand-arm vibration and the effects that it can cause. The course also looks at the control measures that should be taken to reduce exposure to vibration, based on industry best practice.

 

Who is the course for?

All onshore and offshore personnel that use vibration-inducing equipment.


Is there an assessment? 

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

 

Learning objectives

LO1 Describe hand-arm vibration and the effects it can cause 

LO2 Explain what Hand-Arm Vibration Syndrome (HAVS) is and how to identify its early symptoms

LO3 Identify the types of jobs and equipment that are most likely to involve hand-arm vibration and expose workers to the risk of health effects

LO4 Explain the duties of employers under the Control of Vibration at Work Regulations

LO5 Outline the measures that employees can take to reduce the risk of HAVS

LO6 Outline the duties of equipment manufacturers and suppliers in reducing vibration risks

LO7 Describe the process of assessing the vibration risk to employees in accordance with the Exposure Action Value (EAV) and Exposure Limit Value (ELV)

LO8 Describe the control measures that should be taken to reduce exposure to vibration

LO9 Explain the importance of monitoring exposure to vibration, and health surveillance

LO10 Explain the importance of information and training in reducing the risks to health from vibration

Course code: MUK-165
Course type: E-learning course
Duration: 1 hour
Language: English
Price: NOK 1000,-

Who is this course for?

Personnel requiring an awareness or understanding of downhole mechanisms.

 

Is previous experience required?

It is recommended you've had some exposure to drilling operations to undertake this course.

 

How will this course benefit me?

This course aims to introduce learners to the factors affecting hole cleaning, lost circulation and hole enlargement in relation to drilling operations.

 

How will this course benefit my company?

By ensuring you have been introduced to the factors affecting hole cleaning, lost circulation and hole enlargement in relation to drilling operations.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-006-FT
Course type: E-learning course
Duration: N/A
Language: English
Price: NOK 500,-

FAST TRACK is a learning method which provides you with bespoke learning content by identifying any knowledge gaps you may have in a particular subject area.

FAST TRACK is a pre-assessment learning tool which is designed to assess your existing knowledge of a particular subject area. The pre-assessment uses a pool of questions to test your current knowledge. The results of this assessment help identify your personal knowledge gaps. FAST TRACK then automatically creates a bespoke course to address these knowledge gaps.


Course goal: To increase learners’ awareness of the importance of safe manual handling operations and the risks involved with manual handling. The course also aims to outline best practice for the correct handling techniques for safe lifting, and for the pushing and pulling of loads.

This course covers the following learning objectives:

LO1 Define the term ‘manual handling’ and explain the importance of safe manual handling operations

LO2 Identify the types of injuries that may result from manual handling operations

LO3 Identify the legislation that is in place to regulate manual handling operations

LO4 Describe the duties that are placed on employers and employees by the Manual Handling Operations Regulations

LO5 Explain the importance of risk assessing manual handling operations

LO6 Identify the factors to consider when assessing manual handling operations and identify ways of reducing the risks of injury

LO7 Describe good handling techniques for safe lifting and the importance of working within the HSE manual handling risk assessment guidelines

LO8 Describe good handling techniques for pushing and pulling loads

LO9 Explain the training requirements associated with manual handling operations

Course code: MUK-167
Course type: E-learning course
Duration: 1 hour 30 minutes
Language: English
Price: NOK 1000,-

Who is this course for?

Personnel requiring an awareness or understanding of drilling technology.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to provide learners with an introduction to the Oil and Gas Industry and the different stages required for extracting and producing hydrocarbons.

 

How will this course benefit my company?

By ensuring you have an introduction to the Oil and Gas Industry and the different stages required for extracting and producing hydrocarbons.

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: GAS-002
Course type: Blended course
Duration: 3 Days
Language: English / Norwegian
Price: From NOK 9900,-

IGF Advanced Webinar

Lectures will be presented remotely. Participants need a PC/tablet with camera, mic, speaker, pen and paper for the lectures. After enrolment, participant will receive a personal information about the course and code for "log in" to Mintra TrainingPortal. Compendiums for use in the course can be downloaded from TrainingPortal. A personal code for joining the webinar will be sent by Mail.                            

Mandatory requirements for personal COP IGF Advanced:

After fulfilling the lectures (Remotely), participants will need sailing experience (PA) on an IGF vessel and documentation of 3 bunkering’s. They will need to collect the sailing experience after they have recived their IGF Basic certificate. See more info at our homepage: www.gassteknikk.com / IGF COP or NMA's hompage: https://sdir.no 

Course code: MUK-064
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: NOK 500,-

Who is this course for?

Personnel who require awareness and understanding of the hazards and controls of common compressed air uses.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

 

How will this course benefit me?

This course aims to encourage the safe use of compressed air and describes the ways in which compressed air can be dangerous as well as how to minimise the risks of such dangers occurring

 

How will this course benefit my company?

By ensuring you are introducted  to safe use of compressed air and describes the ways in which compressed air can be dangerous as well as how to minimise the risks of such dangers occurring

 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: MUK-021
Course type: E-learning course
Duration: 30 minutes
Language: French (Subtitles)
Price: NOK 500,-

À l'issue de ce cours, vous devriez pouvoir :

• Expliquer l'importance de l'identification des dangers

• Donner des exemples de dangers industriels courants

• Identifier les dangers inhérents au lieu de travail, et

• Comprendre l'importance des mesures de contrôle dans la limitation des risques provenant de dangers

Course code: EXT-004
Course type: E-learning course
Duration: 5 hours
Language: English, Norwegian
Price: NOK 6000,-

This course is made for personnel who organize or perform: planning, installation, inspection and maintenance of Ex equipment.

The course gives an introduction and repetition in different subjects treated in the IEC 60079 Standard (NEK EN 60079).

The course duration is 5 hours and is valid for 5 years

The course can also be taken as a refresher course for Ex maintenance


Themes:

• Fundamental Ex philosophy, refresher

• Preparing and installing electrical equipment in hazardous areas

• Inspection and maintenance of electrical equipment in Ex areas

• Understand what maintenance tasks can be done locally, and what must be performed by an authorized workshop

• Give candidates for CompEx certification a solid background for the theoretical assessment

Course code: MTP-073
Course type: E-learning course
Duration: 30 minutes
Language: English (US)
Price: NOK 500,-

Who is this course for?

This course aims to provide learners with an awareness of US best practice in relation to the values that govern responsible corporate practice and personal behaviors in the workplace.

Is previous experience required?

No previous experience is required. 

How will this course benefit me?

The Code of Conduct course provides an overview of the common values that govern responsible corporate practice and personal behaviour in a company. The course will identify the responsibilities of employees and our common responsibilities toward each other in the workplace. 

You will learn about applicable laws on human rights, equality, discrimination and corruption. During the course, you will be asked to make your own decisions in relevant dilemmas involving sexual harassment, bullying, discrimination and corruption.

How will this course benefit my company?

By ensuring that all personnel are familiar with applicable laws on human rights, equality, discrimination and corruption.

What standards are referred to in this course?

Civil Rights Act 1964

UK Equality Act 2010

The US Foreign Corrupt Practices Act 

The UK Bribery Act 2010

International Labour Organization (ILO)

Is there an assessment?

Yes

Course code: MUK-086
Course type: E-learning course
Duration: 3 hours
Language: English
Price: NOK 1500,-

Who is this course for?

All relevant personnel.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role.

 

How will this course benefit me?

This course aims to provide an introduction to Gas Compression.

 

The course has seven modules:

Module 1: Introduction to Gas Compression

Module 2: Gas Compression Systems

Module 3: Gas Compressors and their Principles

Module 4: Gas Compressors and their Components

Module 5: Gas Compression Systems: Controlling Surge

Module 6: Gas Compression Systems: Start-up and Shutdown

Module 7: Gas Compression Systems: Innovation

 

How will this course benefit my company?

To ensure you have had an introduction to Gas Compression.

 

What standards are referred to in this course?

The course is made according to industry best practice.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.This course has seven modules:

Course code: MUK-068
Course type: E-learning course
Duration: 20 minutes
Language: English
Price: NOK 500,-

Who is this course for?

For all personnel who are involved in working with gas turbines.

 

Is previous experience required?

No previous experience is required to complete this course.

 

How will this course benefit me?

This course aims to provide an introduction to gas turbines and how they are designed and operated.

 

How will this course benefit my company?

The course will benefit companies by ensuring that all relevant personnel have an understanding of gas turbines and how they are designed and operated.

 

What standards are referred to in this course?

No standards or regulations are referenced in this course.

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course code: APP-001
Course type: E-learning course
Duration: 7 hours
Language: English
Price: NOK 4200,-

This course looks at electrical installations in explosive atmospheres. The object of the course is to enable those working in explosive atmospheres to perform their work properly and safely.

 

This course fulfils the requirements for personnel working in explosive atmospheres. Theory is taken from CENELEC and IEC norms.

 

Text, images, videos, animations and 3D simulations will help give you a better understanding of explosive atmospheres and their particular characteristics.

Course code: PRO-016
Course type: E-learning course
Duration: 4-6 hours
Language: Norwegian
Price: NOK 1900,-

COURSE DESCRIPTION

In a risk assessment,  potential events and consequences are considered. In this course, we focus on unwanted events such as failures and accidents. This could be, for example, a gas leak or afire at an oil platform, that equipment stops working during an operation in a hospital, or that an accident occurs during the execution of a work task. The risk analysis process consists of three phases:

1) Planning

2) Risk assessment

3) Risk management

This course shows how these phases can be planned and implemented in practice. There are many guidelines and standards on how a risk assessmentcan be carried out, and many are adapted to particular industries and professional areas. This course presents a general approach that can be used in most industries.

 

 

COURSE CONTENT

•Introduction:What is risk? What is the purpose of a risk assessments?

•Risk assessment and risk management:Description of the steps in a risk assessment, what is important to look out for in the various steps, and how the risk assessment can be applied in risk management.

•Risk analysis methods:There are numerous risk assessment methods that are suitable for looking at different issues. An introduction is given to some of these; Hazid/ course risk analysis, SJA, HAZOP, FMEA and QRA. It’s crucial to choose a method that is well adapted to the problem you are looking at.

 

 

STANDARDS REFERRED TO IN THIS COURSE

- ISO 31000:2018 Risk Management

 

 

HOW WILL THIS COURSE BENEFIT ME, AND MY COMPANY? 

After completing the course, participants should be able to understand what a risk assessment is and have knowledge of the relevant steps. Participants will also have basic knowledge of:

•Different risk analysis methods.

•Choice of risk analysis methods within the three main categories; simplified risk assessment, standard risk assessment and model-based risk assessment. 

•Typical pitfalls for planning and carrying out risk assessments.

•Understanding how risk assessments can contribute to decision support.

 

 

For more information and prices: 

http://www.hseacademy.com

learning@proactima.com

Phone: + 47 4000 1933

Course code: MTP-072
Course type: E-learning course
Duration: 15 minutes
Language: English (US)
Price: NOK 500,-

Who is this course for?

All relevant personnel.

 

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

 

How will this course benefit me?

This course aims to provide an overview of an employees right to implement their 'Stop Work Authority'. This course in Stop Work Authority is divided into and covers the following topics: Imminent danger, stop work procedure, right to refuse work and unsafe conditions.

 

How will this course benefit my company?

By ensuring you are aware of an employees right to omplement their 'Stop Work Authority'.

 

What standards are referred to in this course?

N/A

 

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 100%.

Course code: MUK-006
Course type: E-learning course
Duration: 30 minutes
Language: French (Subtitles)
Price: NOK 500,-

Ce cours vise à vous permettre de :

• Définir le terme « manutention manuelle » et expliquer l'importance de la sécurisation des opérations de manutention manuelle 

• Identifier les types de blessures susceptibles de se produire par suite d’opérations de manutention manuelle 

• Identifier la législation mise en place pour réguler les opérations de manutention manuelle

• Décrire les responsabilités attribuées aux employeurs et aux employés par la législation sur les opérations de manutention manuelle

• Expliquer l'importance de l'évaluation des risques liés aux opérations de manutention manuelle 

• Identifier les facteurs à prendre en compte quand on évalue des opérations de manutention manuelle et identifier les manières de réduire les risques de blessure 

• Décrire les bonnes techniques de manutention pour un levage, une poussée et une traction des charges sûrs, et

• Expliquer les exigences en matière de formation associées aux opérations de manutention manuelle

Course code: MUK-010
Course type: E-learning course
Duration: 35 minutes
Language: French (Subtitles)
Price: NOK 500,-

À l'issue de ce cours, vous devriez pouvoir :

• Identifier les risques inhérents à un travail en hauteur et expliquer l'importance de la planification et de la gestion des risques

• Identifier les exigences législatives et réglementaires qui aident au contrôle des travaux en hauteur

• Décrire les principales méthodes d'accès pour travailler en hauteur et les différents types d'équipement pour le travail en hauteur 

• Décrire la hiérarchie de contrôle pour la gestion et la sélection de l'équipement lié au travail en hauteur

• Expliquer comment utiliser  correctement un harnais de sécurité, et

• Décrire les règles pour travailler avec des échelles et des échafaudages ainsi que l'importance de l'inspection de l'équipement

Course code: VTK-001
Course type: E-learning course
Duration: 45 minutes
Language: English
Price: NOK 950,-

This course provides an introduction to the understanding of gas in high risk work situations.  It describes real dangers and explains about the most common types of gas.  The course provides increased understanding and knowledge of elements of risk when working in areas exposed to gas, and knowledge of how best to protect yourself, and others, using proper equipment. Users shall become acquainted with the possibilities and limitations presented by gas measurement equipment, in relevant situations.

 

Course Content

- Introduction

- Relevant terms

- Air and closed spaces

- Oxygen measurement

- Explosive gases

- Toxic gases

- Conclusion

Hits per page
| 1 ... 8 ... |